CEPHE PROFİLLERİ

Söve nedir? Nasıl Yapılır? | Teknik Özellikleri | EPS Yalıtım Levhası

MİMARİ ESTETİĞİN YAPI TAŞI AKANTUS CEPHE PROFİLLERİ

Uygulama teknikleri

Installation Instructions

1. The temperature must be above 5 ° C for installation.
2. All surfaces must be clean, dry, not dusty, not fat, good conditionand exempt from any debris before installing.
3. Marking the location with using a setsquare or chalk line.
4. Cut the outside corner with the help of a miter saw.
5. Apply the glue with a trowel to the back side of the product or, using an extruder gun.
6. The pieces must be installed while the glue is still wet.
7. Use the same glue for the treatment of joints. Once the glue dries remove the excess glue with the help of sandpaper.
8. Ready for finishing.

Acanthus Jamb Specifications

• 16 kg / m3 density EPS is produced from the insulation plate (TS-825 ÖNORM EN 13499)
• The coating of acrylic plaster on the plate is highly resistant to external conditions.
• Bonding strength minimum of 80 kPa is.
• Flexible and does not crack.
• The interaction with water, why, freezing and thawing, as the UV affected.
• Heat transmission coefficient (= 0.033 - 0,040 W / mK)
• Insulation value is high.
• Economical.
• Fire class B1 is.
• It is not harmful to human health and the environment.
• It does not absorb water.
• It is light, it does not put a burden on the building.
• Suitable for building physics, breathe.
• The application is very easy and practical.
• It can be painted with all kinds of non-solvent-based paints.
• Provides design options, decorate the building.
• Standard lengths of 2000 mm is produced, it can be produced in different lengths.
• TS 825 - according to the EN 13499 standard thermal insulation and thermal insulation adhesive plaster and brick, concrete and plaster surfaces is fixed to the surface by the bonding method.

Wall Cladding Specifications

Wall Cladding Specifications
• 16-18 kg / m3 density EPS is produced from the insulation plate (TS-825 ÖNORM EN 13499)
• The coating of acrylic plaster on the plate is highly resistant to external conditions.
• Bonding strength minimum of 80 kPa is.
• Flexible and does not crack.
• The interaction with water, why, freezing and thawing, as the UV affected.
• Heat transmission coefficient (= 0.033 - 0,040 W / mK)
• Insulation value is high.
• Economical.
• It provides up to 60% based on the shape and location of the thermal insulation structure.
• It pays for itself in 4 years in the fog.
• The system pays for itself within 4 years.
• It is not harmful to human health and the environment.
• It does not absorb water.
• Over time not lose its heat insulation properties.
• It is light, it does not impose a significant burden to the structure.
• Suitable for building physics, breathe.
• Edge does not create a thermal bridge because it is ridden.
• The application is very easy and practical application errors is less.
• It can be painted with all kinds of non-solvent-based paints.
• Provides design options, decorate the building.
• Jamba is compatible with any applicable on them.
• Standard lengths of 2000 mm is produced, it can be produced in different lengths.
• TS 825 - according to the EN 13499 standard thermal insulation and thermal insulation adhesive plaster and brick, concrete and plaster surfaces is fixed to the surface by the bonding method.

EPS INSULATION PLATE

EPS INSULATION PLATE:
Polystyrene foam plates compliant with TS 7316 EN 13163 standard, TSE certified, with thickness compliant to TS 825; density minimum 15-17 Kg/m³, aged as blocks until dimensional stability is insured in indoors, fire protection class B1, not containing recycling medium; other specifications are provided in Table 1.